割縫篩管適用于出砂粒徑大于0.3mm的出砂井防砂。割縫邊緣垂直度好，切邊潤滑、無毛刺，割縫平均。過流面積大，27/8”篩管300條割縫/1.5m，比同規格油管過流面積大2.4倍。全體舉行功能穩固處置，提升了篩管的腐蝕性及功能，可延伸其井下任務壽命。割縫管采用J55或N80石油套管本體加工，強度好，不易變形。內通徑大，易于舉行管串配置。

割縫篩管是在管壁上應用銑刀在銑床上銑削而成，其縫寬度取決于能經過襯管的砂粒粒徑大小，因而，針對不同砂粒，可選擇不同的割縫寬度來舉行防砂，從而到達避免地層出砂的目的。由于銑刀強度的限制，0.3mm以下的割縫寬度難以加工，因而割縫襯管只適用于中一粗粒徑油砂儲層。依據割縫管剖面來看，可分為平行割縫和梯形割縫，目前往往采用橫向梯形割縫構造。

割縫篩管的加工品質次要取決于單條割縫的尺寸精度、縫形規整度、縫腔外表粗拙度和耐腐蝕度以及割縫的軸向散布和周向散布精度。激光切割與傳統機械加工相比具有加工效率高加工精度高加工范圍廣等長處，篩管的加工該當先選用激光加工梯形縫和寬縫的加工難度較大，采用復合變位法和特殊的工藝方案可處理這些技術難題。激光切割篩管的關鍵在于選用合理的工藝參數參數選用不合理睬形成不同的加工品質缺陷，甚至使整根篩管報廢該當不時優化加工工藝參數提升篩管加工品質。